進口直埋式全焊接球閥德國洛克產品中心

進口直埋式全焊接球閥結構特點：

1、直埋式全焊接球閥可以直埋于地下，無需建造高大閥門井，以減少工程造價，在此同時也可以避免操作閥門時造成人員的傷害。

2、直埋式全焊接球閥打開時，閥球把閥座完全包圍，盡管介質有雜質也沖刷不到閥座及球體密封面，由于這種特殊結構使閥門密閉性與管道具有相同壽命。

3、關閉的直埋式焊接球閥介質靜止對球體及密封閥座產生損害，打開的過程球體又把介質靜止時沉積下來的雜物刮掉，閥座下有彈簧補償對壓力和溫度的變化有補償作用，保證不會產生任何泄露。

4、直埋式全焊接球閥可以直接焊于管道節省了法蘭、螺絲、墊片，節約大量物質資源。

5、閥桿防飛結構：在閥桿下部設置臺階，從閥體內部下裝閥桿，防止閥桿飛出。

6、可根據管道的施工及設計要求，調整閥體的長短和閥桿的高度。

Structural features of imported direct buried all welded ball valve:

1. The directly buried all welded ball valve can be directly buried in the ground, without the need to build a large valve well, so as to reduce the project cost, and at the same time, it can also avoid personal injury when operating the valve.

2. When the directly buried all welded ball valve is opened, the valve ball completely surrounds the valve seat. Although the medium has impurities, it can not wash the valve seat and the sealing surface of the ball. Because of this special structure, the valve tightness has the same service life as the pipeline.

3. The closed direct buried welded ball valve will damage the ball and the sealing valve seat when the medium is still. During the opening process, the ball will scrape off the foreign matters deposited when the medium is still. There is a spring compensation under the valve seat, which can compensate the change of pressure and temperature, so as to ensure no leakage.

4. The directly buried all welded ball valve can be directly welded to the pipeline, which saves flange, screw and gasket, and saves a lot of material resources.

5. Anti flying structure of valve rod: steps are set at the lower part of the valve rod, and the valve rod is installed from inside the valve body to prevent the valve rod from flying out.

6. The length of valve body and the height of valve rod can be adjusted according to the construction and design requirements of pipeline.

進口直埋式全焊接球閥規格參數：

1.閥體：碳鋼ST37.0，A106-B；20號鋼

2.球體：不銹鋼304或316

3.閥桿：2Cr13

4.閥桿密封：全氟像膠

5.球體密封：PTFE（PTFE＋C）

6.通徑：DN15～900

7.壓力：PN 16～64

8.工作溫度：-29℃～＋200℃

9.全焊接球閥適應介質：水、石油、天燃氣

進口直埋式全焊接球閥產品簡介 ：

德國洛克《DE LOCKE》進口直埋式全焊接球閥是采用板材鍛壓后焊接而成，重量比栓接結構輕10~20%左右，閥門體積也較小。同時也減少了閥門外漏點，提高了閥門的使用可靠性。選用不同的驅動方式可滿足不同工礦對閥門的控制要求。用于埋地工況的閥門，設計閥門加長桿，維護用長管和控制閥，使在地面就可以控制直埋加長桿全焊接球閥，閥門表面噴涂環氧樹脂，現場管道跨接及陰極保護措施，適應埋地使用環境。

進口直埋式全焊接球閥場合應用：

1 城市燃氣：燃氣輸出管道、主干線及各支線供應管道等。

2 集中供熱：大型供熱設備輸出管線、主干線、支線。

3 熱交換機：管道及各回路啟閉。

4 鋼 鐵 廠：各種流體管道、廢氣排放管道、mei氣和熱力供應管道、燃料供應管道。

5 工業設備：各種熱處理管道、各種工業mei氣和熱力管道。

6 適用場合：供暖系統、供熱區域、工業管道等用途。