進口可調式減壓閥德國洛克

一、進口可調式減壓閥技術參數：

1、公稱壓力PN（MPa）：1.0 - 2.5Mpa

2、工作壓力（MPa）：1.0 1.6 2.5

3、試驗壓力

4、殼體試壓（MPa）：1.5 2.4 3.8

5、密封試壓（MPa）：1.1 1.8 2.5

6、出口壓力調節范圍（Mpa）：0.2~0.8 0.2~1.2 0.2~1.8

7、動靜壓差（Mpa）：0.2

8、出口壓力穩定性相對于進口壓力的變化誤差：±10%

9、適用介質：無雜物的清水、污水

10、介質適宜溫度：0℃~80℃

1. Nominal pressure PN (MPA): 1.0 - 2.5MPa

2. Working pressure (MPA): 1.0 1.6 2.5

3. Test pressure

4. Shell pressure test (MPA): 1.5 2.4 3.8

5. Seal pressure test (MPA): 1.1 1.8 2.5

6. Outlet pressure regulation range (MPA): 0.2 ~ 0.8 0.2 ~ 1.2 0.2 ~ 1.8

7. Dynamic and static pressure difference (MPA): 0.2

8. Variation error of outlet pressure stability relative to inlet pressure: ± 10%

9. Applicable medium: clean water and sewage without sundries

10. Suitable medium temperature: 0 ℃ ~ 80 ℃

二、進口可調式減壓閥結構特點：

1、閥體采用了全通道、直流式、流線型設計。水力損失小，節能效果好。

2、防止水錘效果好，將緩開、止回速閉、緩閉等消除水錘的技術一體化，防止開泵不錘和停泵倒流與水錘對供水管路和水泵的損害。

3、操作方便，無需為閥門另配電控系統，閥門隨水泵的開啟與停止自動并按順序完成控制功能。通過設定調節閥開度可得到合適的控制參數。

1. The valve body adopts full channel, direct current and streamline design. The hydraulic loss is small and the energy saving effect is good.

2. The effect of preventing water hammer is good. The technology of eliminating water hammer, such as slow opening, check quick closing and slow closing, is integrated to prevent water hammer from damaging the water supply pipeline and water pump when the pump is not started or stopped and the backflow of the pump and water hammer.

3. It is easy to operate, no need to provide another electric control system for the valve. The valve will automatically and sequentially complete the control function with the opening and stopping of the water pump. The appropriate control parameters can be obtained by setting the opening of the control valve.

三、進口可調式減壓閥工作原理：

當管道從進水端給水時，水流過針型調節閥進入主閥控制室，出口壓力通過導管作用到導閥上，當出口壓力高于導閥設定值時，導閥關閉，控制室停止排水，此時主閥控制室內壓力升高并關閉主閥，出口壓力不再升高。

當出口壓力降到導閥設定壓力時導閥開啟，控制室向下游排水。由于導閥的排水量大于針型調節閥的進水量，主閥控制室壓力下降，進口壓力使主閥開啟。穩定狀態下，控制室進水、排水相同，開度不變，出口壓力不變。

調節導閥彈簧即可設定出口壓力。

安裝好此閥后，如果出口壓力值不適合現場要求，則可以通過如下方法對此閥進行調節：首先松開減壓導閥平螺母，然后根據現場要求用M6內六角扳手或順時針或逆時針調節調節螺母。順時針調節減壓導閥上的調節螺母時，出口壓力升高；逆時針調節調節螺母時，出口壓力降低。調節到能滿足現場要求后，上好平螺母。

When the pipeline supplies water from the inlet end, the water flows through the needle type regulating valve and enters the control room of the main valve. The outlet pressure acts on the pilot valve through the conduit. When the outlet pressure is higher than the set value of the pilot valve, the pilot valve closes and the control room stops drainage. At this time, the pressure in the control room of the main valve increases and the main valve closes, and the outlet pressure no longer increases.

When the outlet pressure drops to the set pressure of the pilot valve, the pilot valve opens and the control room drains to the downstream. Because the water discharge of the pilot valve is greater than that of the needle type regulating valve, the pressure in the control room of the main valve drops, and the inlet pressure makes the main valve open. In the stable state, the water inlet and drainage of the control room are the same, the opening is unchanged, and the outlet pressure is unchanged.

Adjust the guide valve spring to set the outlet pressure.

After the installation of the valve, if the outlet pressure value is not suitable for the site requirements, the valve can be adjusted by the following methods: first, loosen the flat nut of the pressure reducing pilot valve, and then adjust the adjusting nut with the M6 Allen wrench or clockwise or anticlockwise according to the site requirements. When adjusting the adjusting nut on the pressure reducing pilot valve clockwise, the outlet pressure increases; when adjusting the adjusting nut counterclockwise, the outlet pressure decreases. After adjusting to meet the site requirements, install the flat nut.

四、進口可調式減壓閥描述：

德國LOCKE洛克進口可調式減壓閥是根據水力差動控制原理或水力先導控制（由減壓先導閥控制主閥）原理，以出口壓力的設定值為準，自動調節閥瓣的開啟度和流量，實現出口壓力的減壓和穩定，并與進口壓力的關聯度較小，可通過彈簧調節裝置，對減壓閥出口壓力進行有效調整 。

According to the principle of hydraulic differential control or hydraulic pilot control (the main valve is controlled by the pressure reducing pilot valve) and the set value of the outlet pressure, the locklock imported adjustable pressure reducing valve in Germany can automatically adjust the opening degree and flow of the valve disc, realize the pressure reduction and stability of the outlet pressure, and have a small correlation with the inlet pressure. The outlet pressure of the pressure reducing valve can be adjusted by the spring regulating device The force is adjusted effectively.