預制橋梁防撞墻鋼模具   橋梁防撞墻鋼模具    宏旭制作說明

水泥防撞墻模板   水泥防撞墻鋼模具基本上都是兩片狀的結構，在使用的時候需要將模板運送到施工現場進行現澆加工，因?yàn)榉雷矇Φ牡脑O(shè)置距離與公路的長度是有關的，如果提前進行生產的話會導致制作出來的防撞墻不能夠滿足施工的要求，必須將模具運送到公路周邊在生產的時候需要進行拼接，一塊直板與彎板分開放置，兩塊模板之間的距離就是公路防撞墻墻體的厚度，如果墻體過薄的話就無法達到抗撞擊的效果，一般防撞墻的厚度都是在二十公分以上，具體的厚度需要調整水泥防撞墻模板   水泥防撞墻鋼模具的頂部的拉桿，每次生產的時候調整墻體厚度的話必須將所有的拉桿進行調節。之后在模板的兩側使用鋼板或者是特定的零件進行阻隔，接下來便是可以進行泥漿的澆筑了，大量的混凝土通過管道快速的填滿模板之間，震動過后一些位置的泥漿平面就會下降，自然就需要再去填充一些泥漿，氣泡排除干凈之后就能夠進行晾曬了，等到泥漿徹底凝固后就需要拆開鋼模板就可以了。

Formwork of cement anti-collision wall The steel mold of cement anti-collision wall is basically a two-piece structure. When using, the formwork needs to be transported to the construction site for cast-in-place processing, because the setting distance of the anti-collision wall is related to the length of the road. If the production is carried out in advance, the produced anti-collision wall can not meet the construction requirements, so the mold must be transported to the periphery of the highway during production When splicing is needed, a straight plate and a curved plate are placed separately. The distance between the two templates is the thickness of the highway anti-collision wall wall. If the wall is too thin, the anti-collision effect cannot be achieved. Generally, the thickness of the anti-collision wall is more than 20 cm. The concrete thickness of the concrete anti-collision wall needs to be adjusted The pull rod at the top of the steel mold of the cement anti-collision wall must be adjusted every time the thickness of the wall is adjusted. After that, steel plates or specific parts are used to block the two sides of the formwork. The next step is to pour the slurry. A large amount of concrete is quickly filled between the formwork through the pipeline. After the vibration, the slurry level at some positions will drop. Naturally, it is necessary to fill some mud. After the bubbles are removed, the air can be dried, and the mud can be completely dried After solidification, it is necessary to dismantle the steel formwork.