進口減壓閥德國洛克產品特點（工作原理，安裝須知）

一、進口減壓閥描述：

德國LOCKE洛克生產的進口減壓閥，驅動方式可選用自動，連接方式可選用法蘭，結構形式可選用硬密封，密封結構可選用，壓力范圍PN0MPa-100MPa，公稱通徑為DN15MM-500MM，材質可選用不銹鋼（304、316、316L）、鑄鋼。由于閥門的使用范圍非常的廣泛，同一種閥門在不同的場合與工況有不同的搭配，如果您是非專業人士，歡迎您向本公司來電咨詢。本公司有專業技術人員為您服務！技術部電話：13816999942！

The imported pressure reducing valve manufactured by Locke lock, Germany, can be driven automatically, connected with flange, hard seal and sealing structure, with pressure range of pn0mpa-100mpa, nominal diameter of dn15mm-500mm, and material of stainless steel (304, 316, 316L) and cast steel. Due to the wide range of use of valves, the same valve has different combinations in different occasions and working conditions. If you are a non professional, you are welcome to call our company for consultation. The company has professional and technical personnel for your service! Tel. of Technology Department: 1381699942!

二、進口減壓閥技術參數：

1、產品口徑：DN15-500

2、產品壓力：1.6-100Mpa

3、產品材質：鑄鋼、不銹鋼、合金鋼等

4、適用介質：高溫蒸汽, 空氣、氮氣、氧氣、氫氣、液化氣、天然氣等氣體。 

1. Product diameter: dn15-500

2. Product pressure: 1.6-100mpa

3. Product material: cast steel, stainless steel, alloy steel, etc

4. Applicable medium: high temperature steam, air, nitrogen, oxygen, hydrogen, liquefied gas, natural gas and other gases.

三、進口減壓閥基本性能：

（1） 調壓范圍：它是指減壓閥輸出壓力P2的可調范圍，在此范圍內要求達到規定的精度。調壓范圍主要與調壓彈簧的剛度有關。

（2） 壓力特性：它是指流量g為定值時，因輸入壓力波動而引起輸出壓力波動的特性。輸出壓力波動越小，減壓閥的特性越好。輸出壓力必須低于輸入壓力—定值才基本上不隨輸入壓力變化而變化。

（3） 流量特性：它是指輸入壓力—定時，輸出壓力隨輸出流量g的變化而變化的持性。當流量g發生變化時，輸出壓力的變化越小越好。一般輸出壓力越低，它隨輸出流量的變化波動就越小。

(1) Pressure regulating range: it refers to the adjustable range of the output pressure P2 of the pressure reducing valve, within which the specified accuracy is required. The pressure regulating range is mainly related to the rigidity of the pressure regulating spring.

(2) Pressure characteristic: it refers to the characteristic of output pressure fluctuation caused by input pressure fluctuation when flow G is constant. The smaller the output pressure fluctuation, the better the characteristics of the pressure reducing valve. The output pressure must be lower than the input pressure - set value to basically not change with the input pressure.

(3) Flow characteristics: it refers to the input pressure timing, the output pressure changes with the change of output flow G. When the flow rate G changes, the smaller the change of the output pressure is, the better. Generally, the lower the output pressure is, the smaller its fluctuation with the change of output flow.

四、進口減壓閥安裝和維護:

1、減壓閥為了操作和維護方便，該閥一般直立安裝在水平管道上。

2、減壓閥安裝時應注意使管路中介質的流向與閥休上所示箭頭的方向一致。

3、減壓閥為了防止閥后壓力超壓，應在離閥出口不少于4M處安裝一個減壓閥。

1. For the convenience of operation and maintenance, the pressure reducing valve is generally installed vertically on the horizontal pipeline.

2. When installing the pressure reducing valve, pay attention to make the flow direction of the medium in the pipeline consistent with the direction of the arrow shown on the valve seat.

3. In order to prevent overpressure behind the valve, a pressure reducing valve shall be installed at least 4m away from the valve outlet.